Review of Swan 44 B
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Swan 44 B or similar boat for sale
Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 3 cabins, 6-7 berths, a galley, 340.0 liter fresh water capacity and toilet facility.
The Swan 44 B is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The boat may be equipped with an inboard Perkins diesel engine at 50 hp (37 kW). The speed is 8.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank, which is made of stainless steel, has a capacity of 265.0 liters (70 US gallons, 58 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Swan 44 B is 1.90, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Swan 44 B is about 295 kg/cm, alternatively 1656 lbs/inch.
Meaning: if you load 295 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1656 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Swan 44 B is 30.4.
What is L/B (Length Beam Ratio)?
The l/b ratio for Swan 44 B is 3.21.
What is Displacement Length Ratio?
The DL-ratio for Swan 44 B is 260 which categorizes this boat among 'light crusers & offshore racers'.
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 13.4 m | (44.0 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.4 m | (44.0 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 33.5 m | (109.9 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.5 m | (96.7 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Swan 44 B it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.