Review of Inferno 37
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find an Inferno 37 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The Inferno 37 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
Fin keel
The Inferno 37 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The boat can only enter major marinas as the draft is about 1.89 - 1.99 meter (6.20 - 6.50 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Inferno 37 is 1.90, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Inferno 37 is about 220 kg/cm, alternatively 1235 lbs/inch.
Meaning: if you load 220 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1235 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Inferno 37 is 23.9.
What is L/B (Length Beam Ratio)?
The l/b ratio for Inferno 37 is 3.47.
The ballast ratio for Inferno 37 is 62%.
What is Displacement Length Ratio?
The DL-ratio for Inferno 37 is 188 which categorizes this boat among 'light racers'.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 38m2 (409 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 11.9 m | (39.0 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.9 m | (39.0 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 29.7 m | (97.5 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 26.2 m | (85.8 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Inferno 37 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.