YachtDatabase.com

Review of Tartan 31 Piper


Basic specs.

sail specifications
The Tartan 31 Piper is a sailboat designed by the maritime architect Tim Jackett in the early nineties. The Tartan 31 Piper is built by the American yard Tartan Marine.

Here we would have liked to show you nice photos of the Tartan 31 Piper.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Tartan 31 Piper or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Rig

The Tartan 31 Piper is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

Fin keel

The Tartan 31 Piper is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Yanmar diesel engine


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Tartan 31 Piper is 2.10, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Tartan 31 Piper is about 177 kg/cm, alternatively 991 lbs/inch.
Meaning: if you load 177 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 991 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Tartan 31 Piper is 2.87.

Slim Wide 76% 0 50 100
Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Tartan 31 Piper is 40%.

Low High 46% 0 50 100
This ballast ratio shows a righting moment that is higher than 46% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Tartan 31 Piper is 228 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 62% 0 50 100
62% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Tartan 31 Piper with ISO 8666 reference sail is 18.7, with a 135% genua the SA/D is 22.1.

Low High 79% 0 50 100
The SA/D ratio indicates that it is faster than 79% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 66% 0 50 100
The Tartan 31 Piper has more rig than 66% of all similar sailboats, which indicates that the boat is slightly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 31m2 (333 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 29.5 m(96.8 feet)10 mm(3/8 inch)
Jib/genoa halyard29.5 m(96.8 feet)10 mm(3/8 inch)
Spinnaker halyard29.5 m(96.8 feet)10 mm(3/8 inch)
Jib sheet 9.6 m(31.3 feet)12 mm(1/2 inch)
Genoa sheet9.6 m(31.3 feet)12 mm(1/2 inch)
Mainsheet 23.9 m(78.3 feet)12 mm(1/2 inch)
Spinnaker sheet21.0 m(68.9 feet)12 mm(1/2 inch)
Cunningham4.0 m(13.0 feet)10 mm(3/8 inch)
Kickingstrap7.9 m(26.0 feet)10 mm(3/8 inch)
Clew-outhaul7.9 m(26.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Tartan 31 Piper it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References