YachtDatabase.com

Review of Seawind Mk II Ketch


Basic specs.

sail specifications
The Seawind Mk II Ketch is a sailboat designed by the American maritime architect Thomas C. Gillmer in the mid seventies. The Seawind Mk II Ketch is built by the American yard Allied Boat Co..

Here we would have liked to show you nice photos of the Seawind Mk II Ketch.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Seawind Mk II Ketch or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The boat is equipped with 227.0 liter fresh water capacity.


Rig

The Seawind Mk II Ketch is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.


Keel

Full keel

The Seawind Mk II Ketch is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.


Engine

Seawind Mk II Ketch may be equipped with an inboard Westerbeke diesel engine

The fuel tank has a capacity of 151.0 liters (39 US gallons, 33 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Seawind Mk II Ketch is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Seawind Mk II Ketch is about 165 kg/cm, alternatively 927 lbs/inch.
Meaning: if you load 165 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 927 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Seawind Mk II Ketch is 36.8.

Low High 97% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 97% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Seawind Mk II Ketch is 3.03.

Slim Wide 62% 0 50 100
Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Seawind Mk II Ketch is 39%.

Low High 38% 0 50 100
This ballast ratio shows a righting moment that is higher than 38% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Seawind Mk II Ketch is 401 which categorizes this boat among 'heavy cruisers'.

Heavy Light 4% 0 50 100
4% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Seawind Mk II Ketch with ISO 8666 reference sail is 12.4, with a 135% genua the SA/D is 14.9.

Low High 8% 0 50 100
The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 31% 0 50 100
The Seawind Mk II Ketch has more rig than 31% of all similar sailboats, which indicates that the boat is slightly underrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 27m2 (290 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for ketch rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 27.1 m(88.8 feet)10 mm(3/8 inch)
Jib/genoa halyard27.1 m(88.8 feet)10 mm(3/8 inch)
Spinnaker halyard27.1 m(88.8 feet)10 mm(3/8 inch)
Jib sheet 9.6 m(31.6 feet)12 mm(1/2 inch)
Genoa sheet9.6 m(31.6 feet)12 mm(1/2 inch)
Mainsheet 24.1 m(79.0 feet)12 mm(1/2 inch)
Spinnaker sheet21.2 m(69.5 feet)12 mm(1/2 inch)
Cunningham3.7 m(12.0 feet)10 mm(3/8 inch)
Kickingstrap7.3 m(24.0 feet)10 mm(3/8 inch)
Clew-outhaul7.3 m(24.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Seawind Mk II Ketch it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References