YachtDatabase.com

Review of Saga 36


Basic specs.

sail specifications
The Saga 36 is a sailboat designed by the British maritime architect Alan Pape in the late eighties. The Saga 36 is built by the British yard K.R.Skentelbery & Sons Ltd..

Here we would have liked to show you nice photos of the Saga 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Saga 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Keel

Fin keel

The Saga 36 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can enter most marinas as the draft is just about 1.73 - 1.83 meter (5.68 - 5.98 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Saga 36 is 1.64, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Saga 36 is about 189 kg/cm, alternatively 1059 lbs/inch.
Meaning: if you load 189 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1059 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Saga 36 is 38.2.

Low High 95% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 95% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Saga 36 is 3.32.

Wide Slim 62% 0 50 100
Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Saga 36 is 39%.

Low High 46% 0 50 100
This ballast ratio shows a righting moment that is higher than 46% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Saga 36 is 356 which categorizes this boat among 'heavy cruisers'.

Heavy Light 12% 0 50 100
12% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 13.16


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 32m2 (344 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 10.9 m(35.8 feet)14 mm(0.55 inch)
Genoa sheet10.9 m(35.8 feet)14 mm(0.55 inch)
Mainsheet 27.2 m(89.4 feet)14 mm(0.55 inch)
Spinnaker sheet24.0 m(78.7 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Saga 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References