YachtDatabase.com

Review of Mamba 36


Basic specs.

sail specifications
The Mamba 36 aka Compis 36 is a sailboat designed by the Swedish maritime architect Bernt Andersson in the early eighties. The Mamba 36 is built by the Swedish yard Mamba Boat AB.

Here we would have liked to show you nice photos of the Mamba 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Mamba 36 or similar boat for sale

Hull

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.


Interior

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 4 cabins, 9 berths, a galley, 120.0 liter fresh water capacity and toilet facility.


Rig

The Mamba 36 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

Fin keel

The Mamba 36 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.78 - 1.88 meter (5.84 - 6.14 ft) dependent on the load. See immersion rate below.


Engine

Mamba 36 may be equipped with an inboard Yanmar diesel engine at 27 hp (20 kW). The speed is 7.0 knots.

The transmission is a saildrive.

The fuel tank, which is made of stainless steel, has a capacity of 60.0 liters (15 US gallons, 13 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Mamba 36 is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Mamba 36 is about 200 kg/cm, alternatively 1123 lbs/inch.
Meaning: if you load 200 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1123 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Mamba 36 is 25.4.

Low High 38% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 38% of all similar sailboat designs. This comfort value is just below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Mamba 36 is 3.43.

Wide Slim 76% 0 50 100
Compared with other similar sailboats it is slimmer than 76% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Mamba 36 is 40%.

Low High 54% 0 50 100
This ballast ratio shows a righting moment that is higher than 54% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Mamba 36 is 194 which categorizes this boat among 'light racers'.

Heavy Light 76% 0 50 100
76% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Mamba 36 with ISO 8666 reference sail is 17.3, with a 135% genua the SA/D is 19.9.

Low High 58% 0 50 100
The SA/D ratio indicates that it is faster than 58% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 69% 0 50 100
The Mamba 36 has more rig than 69% of all similar sailboats, which indicates that the boat is slightly overrigged.


RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Mamba 36 is 66

Slow Fast 66% 0 50 100
The relative speed performance is 66 which means that a it is faster than 66% of all similar sailboat designs.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 35m2 (376 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications genoa specifications spinnaker specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 35.4 m(116.2 feet)12 mm(1/2 inch)
Jib/genoa halyard35.4 m(116.2 feet)12 mm(1/2 inch)
Spinnaker halyard35.4 m(116.2 feet)12 mm(1/2 inch)
Jib sheet 11.1 m(36.3 feet)14 mm(0.55 inch)
Genoa sheet11.1 m(36.3 feet)14 mm(0.55 inch)
Mainsheet 27.6 m(90.6 feet)14 mm(0.55 inch)
Spinnaker sheet24.3 m(79.8 feet)14 mm(0.55 inch)
Cunningham4.5 m(14.8 feet)12 mm(1/2 inch)
Kickingstrap9.0 m(29.5 feet)12 mm(1/2 inch)
Clew-outhaul9.0 m(29.5 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Mamba 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References