Review of Cutlass 27

Basic specs.

The Cutlass 27 is a sailboat designed by the maritime architect Eric White together with Alan F. Hill from United Kingdom of Great Britain and Northern Ireland.

Here we would have liked to show you nice photos of the Cutlass 27.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Cutlass 27 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig

The Cutlass 27 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

Full keel

The Cutlass 27 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Cutlass 27 is 1.62, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Cutlass 27 is about 94 kg/cm, alternatively 528 lbs/inch.
Meaning: if you load 94 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 528 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Cutlass 27 is 30.9.

Comparing this ratio with similar sailboats show that it is more comfortable than 96% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Cutlass 27 is 3.56.

Compared with other similar sailboats it is slimmer than 96% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Cutlass 27 is 49%.

This ballast ratio shows a righting moment that is higher than 86% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Cutlass 27 is 368 which categorizes this boat among 'heavy cruisers'.

8% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Cutlass 27 with ISO 8666 reference sail is 11.8, with a 135% genua the SA/D is 13.9.

The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.

Over- / underrigged

The Cutlass 27 has more rig than 15% of all similar sailboats, which indicates that the boat is significantly underrigged.

RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Cutlass 27 is 21

The relative speed performance is 21 which means that a it is faster than 21% of all similar sailboat designs.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 17m² (182 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	20.4 m	(67.0 feet)	8 mm	(5/16 inch)
Jib/genoa halyard	20.4 m	(67.0 feet)	8 mm	(5/16 inch)
Spinnaker halyard	20.4 m	(67.0 feet)	8 mm	(5/16 inch)
Jib sheet	8.2 m	(27.0 feet)	10 mm	(3/8 inch)
Genoa sheet	8.2 m	(27.0 feet)	10 mm	(3/8 inch)
Mainsheet	20.6 m	(67.5 feet)	10 mm	(3/8 inch)
Spinnaker sheet	18.1 m	(59.4 feet)	10 mm	(3/8 inch)
Cunningham	3.0 m	(9.7 feet)	8 mm	(5/16 inch)
Kickingstrap	5.9 m	(19.5 feet)	8 mm	(5/16 inch)
Clew-outhaul	5.9 m	(19.5 feet)	8 mm	(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Cutlass 27 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.