Review of Banner 30

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

Interior of Banner 30 anno 1980.

The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with one cabin, 5 berths, a galley, 30.0 liter fresh water capacity and toilet facility.

Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

The Banner 30 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Keel of Banner 30 anno 1980.

The Banner 30 has been built with different keel alternatives.

Fin keel

One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

Banner 30 can enter most marinas as the draft is just about 1.60 - 1.70 meter (5.25 - 5.55 ft) dependent on the load. See immersion rate below.

Fin keel

Another option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.60 - 1.70 meter (5.25 - 5.55 ft) dependent on the load. See immersion rate below.

The Banner 30 has been equipped with different engine alternatives.

Alternative 1:

An outboard motor is often used on this boat. In that case the boat will typically require a power of 5 - 6 hp, alternatively 120 - 144 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.

Alternative 2:

Banner 30 may be equipped with an inboard engine

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 30.0 liters (7 US gallons, 6 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Banner 30 is 2.03, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Banner 30 is about 133 kg/cm, alternatively 745 lbs/inch.
Meaning: if you load 133 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 745 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Banner 30 is 17.9 - 18.9.

What is L/B (Length Beam Ratio)?

The l/b ratio for Banner 30 is 3.21.

What is a Ballast Ratio?

The ballast ratio for Banner 30 is 44%.

What is Displacement Length Ratio?

The DL-ratio for Banner 30 is 204 which categorizes this boat among 'light crusers & offshore racers'.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Banner 30 with ISO 8666 reference sail is 17.9, with a 135% genua the SA/D is 20.6.

What is Relative Speed Performance?

The Relative Speed Performance for Banner 30 is 90

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 23m² (247 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Banner 30 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.