YachtDatabase.com

Review of Ariel 26


Basic specs.

sail specifications
The Ariel 26 is a sailboat designed by the Swedish maritime architect Carl Alberg in the early sixties. Several hundred boats have been produced. The Ariel 26 is built by the American yard Pearson Yachts.

Here we would have liked to show you nice photos of the Ariel 26.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Ariel 26 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Keel

Full keel

The Ariel 26 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter even shallow marinas as the draft is just about 1.13 - 1.23 meter (3.71 - 4.01 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Universal Atomic 4 gasoline engine at 30 hp (22 kW). Calculated max speed is about 7.7 knots


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Ariel 26 is 1.86, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Ariel 26 is about 92 kg/cm, alternatively 516 lbs/inch.
Meaning: if you load 92 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 516 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Ariel 26 is 23.8.

Low High 79% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 79% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Ariel 26 is 3.20.

Wide Slim 76% 0 50 100
Compared with other similar sailboats it is slimmer than 76% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Ariel 26 is 44%.

Low High 69% 0 50 100
This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Ariel 26 is 360 which categorizes this boat among 'heavy cruisers'.

Heavy Light 7% 0 50 100
7% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 15m2 (161 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 7.8 m(25.6 feet)10 mm(3/8 inch)
Genoa sheet 7.8 m(25.6 feet)10 mm(3/8 inch)
Mainsheet 19.5 m(64.0 feet)10 mm(3/8 inch)
Spinnaker sheet17.2 m(56.3 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Ariel 26 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References