The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The Little Harbor 53 has been built with different keel alternatives.
Unknown keel type
The boat can only enter major marinas as the draft is about 1.89 - 1.99 meter (6.20 - 6.50 ft) dependent on the load. See immersion rate below.
CentreBoard
The Little Harbor 53 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can enter most marinas as the draft is just about 1.73 - 1.83 meter (5.68 - 5.98 ft) dependent on the load. See immersion rate below.
Little Harbor 53 may be equipped with an inboard Westerbeke diesel engine
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Little Harbor 53 is about 403 kg/cm, alternatively 2258 lbs/inch.
Meaning: if you load 403 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 2258 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Little Harbor 53 is 3.51.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 64m2 (688 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Mainsail halyard | 45.6 m | (149.8 feet) | 14 mm | (0.55 inch) |
Jib/genoa halyard | 45.6 m | (149.8 feet) | 14 mm | (0.55 inch) |
Spinnaker halyard | 45.6 m | (149.8 feet) | 14 mm | (0.55 inch) |
Jib sheet | 16.1 m | (52.7 feet) | 16 mm | (5/8 inch) |
Genoa sheet | 16.1 m | (52.7 feet) | 16 mm | (5/8 inch) |
Mainsheet | 40.1 m | (131.7 feet) | 16 mm | (5/8 inch) |
Spinnaker sheet | 35.3 m | (115.9 feet) | 16 mm | (5/8 inch) |
Cunningham | 6.2 m | (20.3 feet) | 14 mm | (0.55 inch) |
Kickingstrap | 12.4 m | (40.6 feet) | 14 mm | (0.55 inch) |
Clew-outhaul | 12.4 m | (40.6 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Little Harbor 53 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.