YachtDatabase.com

Review of Irwin 27


Basic specs.

sail specifications
The Irwin 27 is a sailboat designed by the maritime architect Ted Irwin in the late sixties. The Irwin 27 is built by the American yard Irwin Yachts.

Here we would have liked to show you nice photos of the Irwin 27.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Irwin 27 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Rig

The Irwin 27 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

CentreBoard

The Irwin 27 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 0.81 - 0.91 meter (2.66 - 2.96 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Universal Atomic 4 gasoline engine at 30 hp (22 kW). Calculated max speed is about 7.2 knots


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Irwin 27 is 1.85, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Irwin 27 is about 110 kg/cm, alternatively 619 lbs/inch.
Meaning: if you load 110 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 619 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Irwin 27 is 25.4.

Low High 79% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 79% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Irwin 27 is 3.12.

Wide Slim 62% 0 50 100
Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Irwin 27 is 341 which categorizes this boat among 'heavy cruisers'.

Heavy Light 14% 0 50 100
14% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Irwin 27 with ISO 8666 reference sail is 16.9, with a 135% genua the SA/D is 19.8.

Low High 62% 0 50 100
The SA/D ratio indicates that it is faster than 62% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 24m2 (258 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 25.4 m(83.4 feet)8 mm(5/16 inch)
Jib/genoa halyard25.4 m(83.4 feet)8 mm(5/16 inch)
Spinnaker halyard25.4 m(83.4 feet)8 mm(5/16 inch)
Jib sheet 8.2 m(27.1 feet)10 mm(3/8 inch)
Genoa sheet8.2 m(27.1 feet)10 mm(3/8 inch)
Mainsheet 20.6 m(67.7 feet)10 mm(3/8 inch)
Spinnaker sheet18.2 m(59.5 feet)10 mm(3/8 inch)
Cunningham3.7 m(12.2 feet)8 mm(5/16 inch)
Kickingstrap7.5 m(24.5 feet)8 mm(5/16 inch)
Clew-outhaul7.5 m(24.5 feet)8 mm(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Irwin 27 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References