YachtDatabase.com

Review of Bowman 36


Basic specs.

sail specifications
The Bowman 36 is a sailboat designed by the maritime architect bureau Holman & Pye in the early seventies. The Bowman 36 is built by the British yard Bowman.

Here we would have liked to show you nice photos of the Bowman 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Bowman 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Rig

The Bowman 36 is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.


Keel

Full keel

The Bowman 36 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter most marinas as the draft is just about 1.73 - 1.83 meter (5.68 - 5.98 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Mercedes-Benz diesel engine at 42 hp (31 kW). Calculated max speed is about 5.8 knots


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Bowman 36 is 1.71, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bowman 36 is about 187 kg/cm, alternatively 1052 lbs/inch.
Meaning: if you load 187 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1052 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Bowman 36 is 38.0.

Low High 95% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 95% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Bowman 36 is 3.18.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Bowman 36 is 435 which categorizes this boat among 'heavy cruisers'.

Heavy Light 2% 0 50 100
2% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Bowman 36 with ISO 8666 reference sail is 12.6, with a 135% genua the SA/D is 15.0.

Low High 8% 0 50 100
The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 32m2 (344 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for ketch rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 28.4 m(93.0 feet)12 mm(1/2 inch)
Jib/genoa halyard28.4 m(93.0 feet)12 mm(1/2 inch)
Spinnaker halyard28.4 m(93.0 feet)12 mm(1/2 inch)
Jib sheet 11.0 m(36.0 feet)14 mm(0.55 inch)
Genoa sheet11.0 m(36.0 feet)14 mm(0.55 inch)
Mainsheet 27.4 m(90.0 feet)14 mm(0.55 inch)
Spinnaker sheet24.1 m(79.2 feet)14 mm(0.55 inch)
Cunningham4.3 m(14.2 feet)12 mm(1/2 inch)
Kickingstrap8.7 m(28.4 feet)12 mm(1/2 inch)
Clew-outhaul8.7 m(28.4 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Bowman 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References