The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The deck is a double deck which improves the indoor climate.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 9 berths, a galley, 330.0 liter fresh water capacity and toilet facility.
The Avance 40 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Avance 40 has been built with different keel alternatives.
Fin keel
One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 2.25 - 2.35 meter (7.38 - 7.68 ft) dependent on the load. See immersion rate below.
CentreBoard
Another option is a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.
Avance 40 can enter even shallow marinas as the draft is just about 1.49 - 1.59 meter (4.89 - 5.19 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Bukh diesel engine at 39 hp (29 kW). The speed is 9.0 knots.
The fuel tank, which is made of steel, has a capacity of 115.0 liters (30 US gallons, 25 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Avance 40 is 1.87, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Avance 40 is about 252 kg/cm, alternatively 1411 lbs/inch.
Meaning: if you load 252 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1411 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Avance 40 is 29.9.
What is L/B (Length Beam Ratio)?
The l/b ratio for Avance 40 is 3.18.
The ballast ratio for Avance 40 is 43%.
What is Displacement Length Ratio?
The DL-ratio for Avance 40 is 263 which categorizes this boat among 'light crusers & offshore racers'.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 45m2 (484 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 12.2 m | (40.0 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 12.2 m | (40.0 feet) | 14 mm | (0.55 inch) |
Mainsheet | 30.5 m | (100.1 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 26.8 m | (88.1 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Avance 40 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.