Review of Océanis 440
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find an Océanis 440 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The Océanis 440 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Océanis 440 has been built with different keel alternatives.
Unknown keel type
The boat can only enter major marinas as the draft is about 1.82 - 1.92 meter (5.97 - 6.27 ft) dependent on the load. See immersion rate below.
Wing keel
But be aware that even though a Wing Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.
The boat can only enter major marinas as the draft is about 1.80 - 1.90 meter (5.91 - 6.21 ft) dependent on the load. See immersion rate below.
Océanis 440 may be equipped with an inboard Perkins diesel engine
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Océanis 440 is about 374 kg/cm, alternatively 2098 lbs/inch.
Meaning: if you load 374 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 2098 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Océanis 440 is 3.10.
Maintenance
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 37.1 m | (121.9 feet) | 14 mm | (0.55 inch) |
| Jib/genoa halyard | 37.1 m | (121.9 feet) | 14 mm | (0.55 inch) |
| Spinnaker halyard | 37.1 m | (121.9 feet) | 14 mm | (0.55 inch) |
| Jib sheet | 13.2 m | (43.2 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.2 m | (43.2 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 32.9 m | (107.9 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.0 m | (95.0 feet) | 16 mm | (5/8 inch) |
| Cunningham | 5.2 m | (17.1 feet) | 14 mm | (0.55 inch) |
| Kickingstrap | 10.4 m | (34.1 feet) | 14 mm | (0.55 inch) |
| Clew-outhaul | 10.4 m | (34.1 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Océanis 440 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.