The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 5-7 berths, a galley and 300.0 liter fresh water capacity.
The Hanse 400 is built with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Hanse 400 has been built with different keel alternatives.
Unknown keel type
The boat can enter most marinas as the draft is just about 1.65 - 1.75 meter (5.41 - 5.71 ft) dependent on the load. See immersion rate below.
Unknown keel type
Hanse 400 can only enter major marinas as the draft is about 1.98 - 2.08 meter (6.50 - 6.80 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Yanmar 3JH4 diesel engine at 40 hp (29 kW). Calculated max speed is about 6.5 knots
The transmission is a saildrive.
The fuel tank has a capacity of 140.0 liters (36 US gallons, 30 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Hanse 400 is 2.00, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
Hanse 400 holds a CE certification:
The boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Hanse 400 is about 292 kg/cm, alternatively 1636 lbs/inch.
Meaning: if you load 292 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1636 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Hanse 400 is 25.1.
What is L/B (Length Beam Ratio)?
The l/b ratio for Hanse 400 is 2.97.
What is Displacement Length Ratio?
The DL-ratio for Hanse 400 is 188 which categorizes this boat among 'light racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Hanse 400 with ISO 8666 reference sail is 20.3, with a 135% genua the SA/D is 23.6.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 46m2 (495 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for fractional rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Mainsail halyard | 41.8 m | (137.1 feet) | 12 mm | (1/2 inch) |
Jib/genoa halyard | 41.8 m | (137.1 feet) | 12 mm | (1/2 inch) |
Spinnaker halyard | 41.8 m | (137.1 feet) | 12 mm | (1/2 inch) |
Jib sheet | 12.0 m | (39.3 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 12.0 m | (39.3 feet) | 14 mm | (0.55 inch) |
Mainsheet | 30.0 m | (98.3 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 26.4 m | (86.5 feet) | 14 mm | (0.55 inch) |
Cunningham | 5.6 m | (18.3 feet) | 12 mm | (1/2 inch) |
Kickingstrap | 11.1 m | (36.5 feet) | 12 mm | (1/2 inch) |
Clew-outhaul | 11.1 m | (36.5 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Hanse 400 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.