Review of CDE 850 One Design Racer
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a CDE 850 One Design Racer or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The boat is equipped with 4 berths, a galley and toilet facility.
The CDE 850 One Design Racer is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
Torpedo keel
But be aware that even though a Torpedo keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for CDE 850 One Design Racer is 2.51, indicating that this boat would not be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for CDE 850 One Design Racer is about 171 kg/cm, alternatively 962 lbs/inch.
Meaning: if you load 171 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 962 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for CDE 850 One Design Racer is 2.85.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 17.50
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 8.6 m | (28.1 feet) | 10 mm | (3/8 inch) |
| Genoa sheet | 8.6 m | (28.1 feet) | 10 mm | (3/8 inch) |
| Mainsheet | 21.4 m | (70.1 feet) | 10 mm | (3/8 inch) |
| Spinnaker sheet | 18.8 m | (61.7 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for CDE 850 One Design Racer it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.