Review of Yamaha 33

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

The boat is equipped with 170.0 liter fresh water capacity.

The Yamaha 33 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Fin keel

The Yamaha 33 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can only enter major marinas as the draft is about 1.90 - 2.00 meter (6.23 - 6.53 ft) dependent on the load. See immersion rate below.

The Yamaha 33 has been equipped with different engine alternatives.

Alternative 1:

Yamaha 33 may be equipped with an inboard Yanmar YSM12 diesel engine

Alternative 2:

The boat may be equipped with an inboard Yanmar diesel engine at 12 hp (8 kW). Calculated max speed is about 4.3 knots

The fuel tank has a capacity of 70.0 liters (18 US gallons, 15 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Yamaha 33 is 2.06, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Yamaha 33 is about 184 kg/cm, alternatively 1030 lbs/inch.
Meaning: if you load 184 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1030 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Yamaha 33 is 21.2.

What is L/B (Length Beam Ratio)?

The l/b ratio for Yamaha 33 is 3.04.

What is a Ballast Ratio?

The ballast ratio for Yamaha 33 is 45%.

What is Displacement Length Ratio?

The DL-ratio for Yamaha 33 is 222 which categorizes this boat among 'light crusers & offshore racers'.

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 17.30

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 32m² (344 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Yamaha 33 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.