YachtDatabase.com

Review of Oyster 435


Basic specs.

sail specifications
The Oyster 435 is a large sailboat designed by the maritime architect bureau Holman & Pye in the mid eighties. The Oyster 435 is built by the British yard Oyster Marine Ltd..

Here we would have liked to show you nice photos of the Oyster 435.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Oyster 435 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 681.0 liter fresh water capacity.


Keel

Fin keel

The Oyster 435 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can only enter major marinas as the draft is about 1.98 - 2.08 meter (6.50 - 6.80 ft) dependent on the load. See immersion rate below.


Engine

Oyster 435 may be equipped with an inboard Volvo Penta MD30A diesel engine at 62 hp (46 kW). Calculated max speed is about 6.5 knots

The fuel tank has a capacity of 341.0 liters (90 US gallons, 75 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oyster 435 is 1.77, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oyster 435 is about 315 kg/cm, alternatively 1764 lbs/inch.
Meaning: if you load 315 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1764 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Oyster 435 is 36.2.

Low High 73% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 73% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oyster 435 is 3.16.

Slim Wide 73% 0 50 100
Compared with other similar sailboats it is more spacy than 73% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Oyster 435 is 37%.

Low High 42% 0 50 100
This ballast ratio shows a righting moment that is higher than 42% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Oyster 435 is 266 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 38% 0 50 100
38% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 13.82


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 52m2 (559 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 13.2 m(43.4 feet)16 mm(5/8 inch)
Genoa sheet13.2 m(43.4 feet)16 mm(5/8 inch)
Mainsheet 33.1 m(108.4 feet)16 mm(5/8 inch)
Spinnaker sheet29.1 m(95.4 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Oyster 435 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References