The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 370.0 liter fresh water capacity.
The Oceanis 45 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Oceanis 45 has been built with different keel alternatives.
Deep keel
One option is a deep keel. A deep keel provide a better healing moment than a shallow keel.
The boat can only enter major marinas as the draft is about 2.27 - 2.37 meter (7.45 - 7.75 ft) dependent on the load. See immersion rate below.
Shallow keel
Another option is a shallow keel. A shallow keel allow to sail both coastal and inland waters.
Oceanis 45 can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard engine at 54 hp (40 kW). Calculated max speed is about 7.4 knots
The fuel tank has a capacity of 200.0 liters (52 US gallons, 43 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Oceanis 45 is 2.07, indicating that this boat would not be accepted to participate in ocean races.
Oceanis 45 holds three CE certifications:
If less than 10 in on board the boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Oceanis 45 is about 391 kg/cm, alternatively 2191 lbs/inch.
Meaning: if you load 391 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 2191 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Oceanis 45 is 22.9.
What is L/B (Length Beam Ratio)?
The l/b ratio for Oceanis 45 is 3.00.
What is Displacement Length Ratio?
The DL-ratio for Oceanis 45 is 134 which categorizes this boat among 'ultra light racers'.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 66m2 (710 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 13.5 m | (44.3 feet) | 16 mm | (5/8 inch) |
Genoa sheet | 13.5 m | (44.3 feet) | 16 mm | (5/8 inch) |
Mainsheet | 33.8 m | (110.7 feet) | 16 mm | (5/8 inch) |
Spinnaker sheet | 29.7 m | (97.4 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Oceanis 45 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.