Review of Malö 38

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 3 cabins, 7 berths, a galley, 220.0 liter fresh water capacity, toilet facility and 70.0 liter waste water capacity.

The Malö 38 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Fin keel

The Malö 38 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

The Malö 38 has been equipped with different engine alternatives.

Alternative 1:

Malö 38 may be equipped with an inboard Yanmar 4JH2-E diesel engine at 43 hp (32 kW). Calculated max speed is about 7.1 knots

Alternative 2:

The boat may be equipped with an inboard Yanmar diesel engine at 47 hp (35 kW). Calculated max speed is about 7.4 knots

The fuel tank has a capacity of 220.0 liters (58 US gallons, 48 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Malö 38 is 1.82, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Malö 38 is about 207 kg/cm, alternatively 1163 lbs/inch.
Meaning: if you load 207 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1163 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Malö 38 is 27.5.

What is L/B (Length Beam Ratio)?

The l/b ratio for Malö 38 is 3.46.

What is a Ballast Ratio?

The ballast ratio for Malö 38 is 46%.

What is Displacement Length Ratio?

The DL-ratio for Malö 38 is 232 which categorizes this boat among 'light crusers & offshore racers'.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 35m² (376 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Malö 38 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.