Review of Luders 44
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Luders 44 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The Luders 44 is equipped with a yawl rig. A yawl rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a yawl allows for better comfort and stability when sailing downwind or on a broad reach.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Luders 44 is 1.52, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Luders 44 is about 207 kg/cm, alternatively 1162 lbs/inch.
Meaning: if you load 207 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1162 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Luders 44 is 45.0.
What is L/B (Length Beam Ratio)?
The l/b ratio for Luders 44 is 3.99.
What is Displacement Length Ratio?
The DL-ratio for Luders 44 is 406 which categorizes this boat among 'heavy cruisers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Luders 44 with ISO 8666 reference sail is 16.0, with a 135% genua the SA/D is 18.9.
Maintenance
Dimensions of sail.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 36.7 m | (120.5 feet) | 14 mm | (0.55 inch) |
| Jib/genoa halyard | 36.7 m | (120.5 feet) | 14 mm | (0.55 inch) |
| Spinnaker halyard | 36.7 m | (120.5 feet) | 14 mm | (0.55 inch) |
| Jib sheet | 13.5 m | (44.2 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.5 m | (44.2 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 33.7 m | (110.5 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.6 m | (97.2 feet) | 16 mm | (5/8 inch) |
| Cunningham | 5.5 m | (18.0 feet) | 14 mm | (0.55 inch) |
| Kickingstrap | 11.0 m | (36.0 feet) | 14 mm | (0.55 inch) |
| Clew-outhaul | 11.0 m | (36.0 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Luders 44 (1963) it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.