YachtDatabase.com

Review of Kelt 5.50


Basic specs.

sail specifications
The Kelt 5.50 is a small sailboat designed by the French maritime architect Gilles Ollier in the early eighties. The Kelt 5.50 is built by the French yard Kelt Marine Inc..

Here we would have liked to show you nice photos of the Kelt 5.50.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Kelt 5.50 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Rig

The Kelt 5.50 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

The Kelt 5.50 has been built with different keel alternatives.

Unknown keel type

The boat can enter even shallow marinas as the draft is just about 0.98 - 1.08 meter (3.22 - 3.52 ft) dependent on the load. See immersion rate below.

Unknown keel type

The boat can sail close to the beach as the draft is just 0.30 - 0.40 meter (0.98 - 1.28 ft) dependent of the load. See immersion rate below.

Fin keel

The Kelt 5.50 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

Kelt 5.50 can enter even shallow marinas as the draft is just about 0.75 - 0.85 meter (2.46 - 2.76 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Kelt 5.50 is about 84 kg/cm, alternatively 474 lbs/inch.
Meaning: if you load 84 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 474 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Kelt 5.50 is 2.33.

Slim Wide 86% 0 50 100
Compared with other similar sailboats it is more spacy than 86% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 5.4 m(17.8 feet)8 mm(5/16 inch)
Genoa sheet5.4 m(17.8 feet)8 mm(5/16 inch)
Mainsheet 13.6 m(44.5 feet)8 mm(5/16 inch)
Spinnaker sheet11.9 m(39.2 feet)8 mm(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Kelt 5.50 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References