Review of Hunter 340
Basic specs.
Looking for a new boat? Find a Hunter 340 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 3 cabins, 7 berths, a galley, 285.0 liter fresh water capacity, toilet facility and 110.0 liter waste water capacity.
The Hunter 340 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Hunter 340 has been built with different keel alternatives.
Fin keel
The Hunter 340 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.
Unknown keel type
Hunter 340 can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Yanmar diesel engine at 27 hp (20 kW). Calculated max speed is about 6.2 knots
The fuel tank has a capacity of 110.0 liters (29 US gallons, 24 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Hunter 340 is 2.09, indicating that this boat would not be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Hunter 340 is about 206 kg/cm, alternatively 1155 lbs/inch.
Meaning: if you load 206 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1155 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Hunter 340 is 21.5.
What is L/B (Length Beam Ratio)?
The l/b ratio for Hunter 340 is 2.88.
The ballast ratio for Hunter 340 is 37%.
What is Displacement Length Ratio?
The DL-ratio for Hunter 340 is 211 which categorizes this boat among 'light crusers & offshore racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Hunter 340 with ISO 8666 reference sail is 19.5, with a 135% genua the SA/D is 22.3.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 35m2 (376 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for fractional rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 35.2 m | (115.5 feet) | 10 mm | (3/8 inch) |
| Jib/genoa halyard | 35.2 m | (115.5 feet) | 10 mm | (3/8 inch) |
| Spinnaker halyard | 35.2 m | (115.5 feet) | 10 mm | (3/8 inch) |
| Jib sheet | 10.2 m | (33.5 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 10.2 m | (33.5 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 25.5 m | (83.7 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 22.4 m | (73.6 feet) | 12 mm | (1/2 inch) |
| Cunningham | 4.9 m | (16.0 feet) | 10 mm | (3/8 inch) |
| Kickingstrap | 9.8 m | (32.0 feet) | 10 mm | (3/8 inch) |
| Clew-outhaul | 9.8 m | (32.0 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Hunter 340 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.