YachtDatabase.com

Review of Hanse 292


Basic specs.

sail specifications
The Hanse 292 is a sailboat designed in the early thirties. The Hanse 292 is built by the German yard YZG.

Here we would have liked to show you nice photos of the Hanse 292.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Hanse 292 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The boat is equipped with 4 berths, a galley and toilet facility.


Keel

Fin keel

The Hanse 292 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.68 - 1.78 meter (5.51 - 5.81 ft) dependent on the load. See immersion rate below.


Engine

The Hanse 292 has been equipped with different engine alternatives.

Alternative 1:

Hanse 292 may be equipped with an inboard Volvo Penta MD2010 diesel engine at 10 hp (7 kW).

Alternative 2:

The boat may be equipped with an engine at 9 hp (6 kW)..


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hanse 292 is 1.95, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hanse 292 is about 167 kg/cm, alternatively 937 lbs/inch.
Meaning: if you load 167 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 937 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hanse 292 is 3.23.

Wide Slim 66% 0 50 100
Compared with other similar sailboats it is slimmer than 66% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hanse 292 is 36%.

Low High 24% 0 50 100
This ballast ratio shows a righting moment that is higher than 24% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 9.0 m(29.5 feet)10 mm(3/8 inch)
Genoa sheet9.0 m(29.5 feet)10 mm(3/8 inch)
Mainsheet 22.5 m(73.7 feet)10 mm(3/8 inch)
Spinnaker sheet19.8 m(64.9 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Hanse 292 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References