YachtDatabase.com

Review of Yamaha 30 Mk I


Basic specs.

sail specifications
The Yamaha 30 Mk I is a sailboat designed by the Japanese maritime architect bureau Yamaha Design Group in the late seventies. The Yamaha 30 Mk I is built by the Japanese yard Yamaha.

Here we would have liked to show you nice photos of the Yamaha 30 Mk I.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Yamaha 30 Mk I or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Rig

The Yamaha 30 Mk I is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

Fin keel

The Yamaha 30 Mk I is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Yanmar YSM12 diesel engine


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Yamaha 30 Mk I is 2.15, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Yamaha 30 Mk I is about 155 kg/cm, alternatively 868 lbs/inch.
Meaning: if you load 155 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 868 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Yamaha 30 Mk I is 19.9.

Low High 31% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 31% of all similar sailboat designs. This comfort value is just below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Yamaha 30 Mk I is 2.79.

Slim Wide 79% 0 50 100
Compared with other similar sailboats it is more spacy than 79% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Yamaha 30 Mk I is 258 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 50% 0 50 100
50% of all similar sailboat designs are categorized as heavier. This boat has a precise average ratio between displacement and length!


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Yamaha 30 Mk I with ISO 8666 reference sail is 16.2, with a 135% genua the SA/D is 19.5.

Low High 54% 0 50 100
The SA/D ratio indicates that it is faster than 54% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 27m2 (290 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 26.3 m(86.3 feet)8 mm(5/16 inch)
Jib/genoa halyard26.3 m(86.3 feet)8 mm(5/16 inch)
Spinnaker halyard26.3 m(86.3 feet)8 mm(5/16 inch)
Jib sheet 9.0 m(29.4 feet)10 mm(3/8 inch)
Genoa sheet9.0 m(29.4 feet)10 mm(3/8 inch)
Mainsheet 22.4 m(73.6 feet)10 mm(3/8 inch)
Spinnaker sheet19.7 m(64.7 feet)10 mm(3/8 inch)
Cunningham3.0 m(9.8 feet)8 mm(5/16 inch)
Kickingstrap6.0 m(19.7 feet)8 mm(5/16 inch)
Clew-outhaul6.0 m(19.7 feet)8 mm(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Yamaha 30 Mk I it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References