Review of Trias

Basic specs.

The Trias is a sailboat designed by the German maritime architect Helmut Stöberl.

Here we would have liked to show you nice photos of the Trias.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Trias or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Keel

Unknown keel type

The boat can enter even shallow marinas as the draft is just about 1.48 - 1.58 meter (4.86 - 5.16 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Trias is 1.93, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Trias is about 131 kg/cm, alternatively 736 lbs/inch.
Meaning: if you load 131 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 736 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Trias is 4.29.

Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Trias is 44%.

This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 23.56

RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Trias is 90

The relative speed performance is 90 which means that a it is faster than 90% of all similar sailboat designs.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	9.2 m	(30.1 feet)	12 mm	(1/2 inch)
Genoa sheet	9.2 m	(30.1 feet)	12 mm	(1/2 inch)
Mainsheet	22.9 m	(75.2 feet)	12 mm	(1/2 inch)
Spinnaker sheet	20.2 m	(66.2 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Trias it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.