Review of Saare 38
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Saare 38 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 4 berths.
The Saare 38 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
Fin keel
The Saare 38 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The boat can only enter major marinas as the draft is about 1.95 - 2.05 meter (6.40 - 6.70 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Saare 38 is 1.81, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Saare 38 is about 279 kg/cm, alternatively 1565 lbs/inch.
Meaning: if you load 279 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1565 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Saare 38 is 3.11.
The ballast ratio for Saare 38 is 36%.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Saare 38 with ISO 8666 reference sail is 16.3, with a 135% genua the SA/D is 19.1.
Maintenance
Dimensions of sail for fractional rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 37.0 m | (121.6 feet) | 12 mm | (1/2 inch) |
| Jib/genoa halyard | 37.0 m | (121.6 feet) | 12 mm | (1/2 inch) |
| Spinnaker halyard | 37.0 m | (121.6 feet) | 12 mm | (1/2 inch) |
| Jib sheet | 11.4 m | (37.4 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.4 m | (37.4 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 28.5 m | (93.5 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 25.1 m | (82.3 feet) | 14 mm | (0.55 inch) |
| Cunningham | 4.8 m | (15.9 feet) | 12 mm | (1/2 inch) |
| Kickingstrap | 9.7 m | (31.8 feet) | 12 mm | (1/2 inch) |
| Clew-outhaul | 9.7 m | (31.8 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Saare 38 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.