Review of Oceanis 461
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find an Oceanis 461 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 8/10 berths and 550.0 liter fresh water capacity.
The Oceanis 461 has been built with different keel alternatives.
Unknown keel type
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.
The boat can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.
Unknown keel type
Oceanis 461 can enter most marinas as the draft is just about 1.73 - 1.83 meter (5.68 - 5.98 ft) dependent on the load. See immersion rate below.
The Oceanis 461 has been equipped with different engine alternatives.
Alternative 1:
The boat may be equipped with an inboard Yanmar 4JH2-E diesel engine
Alternative 2:
The boat may be equipped with an engine at 56 hp (41 kW)..
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Oceanis 461 is 2.03, indicating that this boat would not be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Oceanis 461 is about 399 kg/cm, alternatively 2237 lbs/inch.
Meaning: if you load 399 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 2237 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Oceanis 461 is 3.29.
The ballast ratio for Oceanis 461 is 35%.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 22.67
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 14.0 m | (45.9 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 14.0 m | (45.9 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 35.0 m | (114.8 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 30.8 m | (101.0 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Oceanis 461 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.