Review of Oceanis 411 Clipper

Oceanis 411 Clipper.

Basic specs.

The Oceanis 411 Clipper aka Beneteau Oceanis Clipper 411 is a large sailboat designed by the French maritime architect Jean-Marie Finot in the late nineties. The Oceanis 411 Clipper is built by the French yard Bénéteau.

Looking for a new boat? Find a Oceanis 411 Clipper or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The interior is like few other boats made in cherry.
The boat is equipped with 0 cabins, 5-7 berths, a galley and 550.0 liter fresh water capacity.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Oceanis 411 Clipper has been built with different keel alternatives.

Unknown keel type

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

Unknown keel type

Oceanis 411 Clipper can only enter major marinas as the draft is about 2.00 - 2.10 meter (6.56 - 6.86 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Volvo Penta 22 L engine at 50 hp (37 kW). Calculated max speed is about 7.6 knots

The fuel tank has a capacity of 150.0 liters (39 US gallons, 32 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oceanis 411 Clipper is 2.01, indicating that this boat would not be accepted to participate in ocean races.

EU classification

Oceanis 411 Clipper holds one CE certification:

If less than 10 in on board the boat is by European Union certified as Class A. OCEAN:

Designed for extended voyages where conditions may exceed wind force 8 (Beaufort scale) and significant wave heights of 4 m and above but excluding abnormal conditions, and vessels largely self-sufficient.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oceanis 411 Clipper is about 291 kg/cm, alternatively 1630 lbs/inch.
Meaning: if you load 291 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1630 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Oceanis 411 Clipper is 23.3.

Comparing this ratio with similar sailboats show that it is more comfortable than 21% of all similar sailboat designs. This is a comfort value significantly below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oceanis 411 Clipper is 3.12.

Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Oceanis 411 Clipper is 32%.

This ballast ratio shows a righting moment that is higher than 15% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Oceanis 411 Clipper is 163 which categorizes this boat among 'light racers'.

85% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 21.46

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 47m² (505 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	12.3 m	(40.5 feet)	14 mm	(0.55 inch)
Genoa sheet	12.3 m	(40.5 feet)	14 mm	(0.55 inch)
Mainsheet	30.9 m	(101.2 feet)	14 mm	(0.55 inch)
Spinnaker sheet	27.1 m	(89.1 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Oceanis 411 Clipper it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.