Review of Moody 30
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Moody 30 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The Moody 30 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Moody 30 has been built with different keel alternatives.
Unknown keel type
The boat can enter most marinas as the draft is just about 1.55 - 1.65 meter (5.09 - 5.39 ft) dependent on the load. See immersion rate below.
Fin keel
The Moody 30 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The boat can enter even shallow marinas as the draft is just about 1.45 - 1.55 meter (4.76 - 5.06 ft) dependent on the load. See immersion rate below.
Moody 30 may be equipped with an inboard Volvo Penta MD11C diesel engine at 23 hp (17 kW).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Moody 30 is about 190 kg/cm, alternatively 1066 lbs/inch.
Meaning: if you load 190 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1066 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Moody 30 is 2.96.
Maintenance
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 24.2 m | (79.2 feet) | 10 mm | (3/8 inch) |
| Jib/genoa halyard | 24.2 m | (79.2 feet) | 10 mm | (3/8 inch) |
| Spinnaker halyard | 24.2 m | (79.2 feet) | 10 mm | (3/8 inch) |
| Jib sheet | 9.2 m | (30.1 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 9.2 m | (30.1 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 22.9 m | (75.2 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 20.2 m | (66.2 feet) | 12 mm | (1/2 inch) |
| Cunningham | 3.6 m | (11.8 feet) | 10 mm | (3/8 inch) |
| Kickingstrap | 7.2 m | (23.6 feet) | 10 mm | (3/8 inch) |
| Clew-outhaul | 7.2 m | (23.6 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Moody 30 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.