Review of Hallberg-Rassy 42F
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Hallberg-Rassy 42F or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 6/8 berths and 685.0 liter fresh water capacity.
The Hallberg-Rassy 42F is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
Fin keel
The Hallberg-Rassy 42F is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 2.08 - 2.18 meter (6.82 - 7.12 ft) dependent on the load. See immersion rate below.
Hallberg-Rassy 42F may be equipped with an inboard Volvo Penta TMD 22 diesel engine at 76 hp (56 kW).
The fuel tank has a capacity of 420.0 liters (110 US gallons, 92 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Hallberg-Rassy 42F is 1.71, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Hallberg-Rassy 42F is about 348 kg/cm, alternatively 1949 lbs/inch.
Meaning: if you load 348 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1949 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Hallberg-Rassy 42F is 3.36.
The ballast ratio for Hallberg-Rassy 42F is 38%.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 16.80
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 13.2 m | (43.4 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.2 m | (43.4 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 33.1 m | (108.4 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.1 m | (95.4 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Hallberg-Rassy 42F it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.