YachtDatabase.com

Review of Gib'Sea Plus 90


Basic specs.

sail specifications
The Gib'Sea Plus 90 is a sailboat designed by the maritime architect Jacques Fauroux. The Gib'Sea Plus 90 is built by the French yard Gibert Marine.

Here we would have liked to show you nice photos of the Gib'Sea Plus 90.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Gib'Sea Plus 90 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The boat is equipped with 6 berths.


Keel

Unknown keel type

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.


Engine

Gib'Sea Plus 90 may be equipped with an inboard diesel engine at 15 hp (11 kW).

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Gib'Sea Plus 90 is 2.35, indicating that this boat would not be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Gib'Sea Plus 90 is about 194 kg/cm, alternatively 1086 lbs/inch.
Meaning: if you load 194 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1086 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Gib'Sea Plus 90 is 2.83.

Slim Wide 76% 0 50 100
Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 27.96


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 9.1 m(29.7 feet)12 mm(1/2 inch)
Genoa sheet9.1 m(29.7 feet)12 mm(1/2 inch)
Mainsheet 22.6 m(74.2 feet)12 mm(1/2 inch)
Spinnaker sheet19.9 m(65.3 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Gib'Sea Plus 90 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References