Review of Faurby 360

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 3 cabins, 6 berths, a galley, 200.0 liter fresh water capacity, toilet facility and 45.0 liter waste water capacity.

The boat has more than one rig.

One option is a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Fin keel

The Faurby 360 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

Faurby 360 can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

The Faurby 360 has been equipped with different engine alternatives.

Alternative 1:

The boat may be equipped with an inboard Volvo Penta MD2030 diesel engine

The transmission is a saildrive.

Alternative 2:

The boat may be equipped with an inboard Volvo Penta D1-30 diesel engine at 27 hp (20 kW). Calculated max speed is about 6.4 knots

The transmission is a saildrive.

The fuel tank, which is made of stainless steel, has a capacity of 65.0 liters (17 US gallons, 14 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Faurby 360 is 1.74, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Faurby 360 is about 194 kg/cm, alternatively 1091 lbs/inch.
Meaning: if you load 194 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1091 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Faurby 360 is 25.5.

What is L/B (Length Beam Ratio)?

The l/b ratio for Faurby 360 is 3.66.

What is a Ballast Ratio?

The ballast ratio for Faurby 360 is 39%.

What is Displacement Length Ratio?

The DL-ratio for Faurby 360 is 160 which categorizes this boat among 'light racers'.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 34m² (365 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Faurby 360 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.