Review of Delphia 33
Basic specs.
Looking for a new boat? Find a Delphia 33 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 2 cabins, 4 berths, a galley, 200.0 liter fresh water capacity, toilet facility and 45.0 liter waste water capacity.
The Delphia 33 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Delphia 33 has been built with different keel alternatives.
Unknown keel type
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 1.80 - 1.90 meter (5.91 - 6.21 ft) dependent on the load. See immersion rate below.
Unknown keel type
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.
Delphia 33 can only enter major marinas as the draft is about 1.80 - 1.90 meter (5.91 - 6.21 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Volvo Penta D1-20 diesel engine
The transmission is a saildrive.
The fuel tank, which is made of stainless steel, has a capacity of 100.0 liters (26 US gallons, 21 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Delphia 33 is 2.08, indicating that this boat would not be accepted to participate in ocean races.
Delphia 33 holds a CE certification:
The boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Delphia 33 is about 217 kg/cm, alternatively 1217 lbs/inch.
Meaning: if you load 217 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1217 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Delphia 33 is 20.3.
What is L/B (Length Beam Ratio)?
The l/b ratio for Delphia 33 is 2.87.
The ballast ratio for Delphia 33 is 28%.
What is Displacement Length Ratio?
The DL-ratio for Delphia 33 is 163 which categorizes this boat among 'light racers'.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 37m2 (398 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 9.9 m | (32.6 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 9.9 m | (32.6 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 24.9 m | (81.6 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 21.9 m | (71.8 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Delphia 33 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.