YachtDatabase.com

Review of Capri 30 (Chris-Craft)


Basic specs.

sail specifications
The Capri 30 (Chris-Craft) is a sailboat designed by the American maritime architect bureau Sparkman & Stephens in the mid sixties. The Capri 30 (Chris-Craft) is built by the American yard Chris-Craft.

Here we would have liked to show you nice photos of the Capri 30 (Chris-Craft).
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Capri 30 (Chris-Craft) or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The boat is equipped with 120.0 liter fresh water capacity.


Keel

The Capri 30 (Chris-Craft) has been built with different keel alternatives.

Unknown keel type

The boat can enter even shallow marinas as the draft is just about 1.16 - 1.26 meter (3.81 - 4.11 ft) dependent on the load. See immersion rate below.

CentreBoard

The Capri 30 (Chris-Craft) is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

Capri 30 (Chris-Craft) can enter even shallow marinas as the draft is just about 1.14 - 1.24 meter (3.74 - 4.04 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Capri 30 (Chris-Craft) is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Capri 30 (Chris-Craft) is about 150 kg/cm, alternatively 843 lbs/inch.
Meaning: if you load 150 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 843 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Capri 30 (Chris-Craft) is 33.1.

Low High 93% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 93% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Capri 30 (Chris-Craft) is 3.10.

Slim Wide 50% 0 50 100
Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Capri 30 (Chris-Craft) is 335 which categorizes this boat among 'heavy cruisers'.

Heavy Light 18% 0 50 100
18% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Capri 30 (Chris-Craft) with ISO 8666 reference sail is 14.7, with a 135% genua the SA/D is 17.2.

Low High 31% 0 50 100
The SA/D ratio indicates that it is faster than 31% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 23m2 (247 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 27.6 m(90.6 feet)10 mm(3/8 inch)
Jib/genoa halyard27.6 m(90.6 feet)10 mm(3/8 inch)
Spinnaker halyard27.6 m(90.6 feet)10 mm(3/8 inch)
Jib sheet 9.1 m(30.0 feet)12 mm(1/2 inch)
Genoa sheet9.1 m(30.0 feet)12 mm(1/2 inch)
Mainsheet 22.9 m(75.0 feet)12 mm(1/2 inch)
Spinnaker sheet20.1 m(66.0 feet)12 mm(1/2 inch)
Cunningham4.3 m(14.0 feet)10 mm(3/8 inch)
Kickingstrap8.5 m(28.0 feet)10 mm(3/8 inch)
Clew-outhaul8.5 m(28.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Capri 30 (Chris-Craft) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References