YachtDatabase.com

Review of C&C 1/2 Ton


Basic specs.

sail specifications
The C&C 1/2 Ton is a sailboat designed by the maritime architect bureau Cuthbertson & Cassian in the late seventies. The C&C 1/2 Ton is built by the American yard C&C Yachts.

Here we would have liked to show you nice photos of the C&C 1/2 Ton.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a C&C 1/2 Ton or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Rig

The C&C 1/2 Ton is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

Fin keel

The C&C 1/2 Ton is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.62 - 1.72 meter (5.31 - 5.61 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for C&C 1/2 Ton is 2.21, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for C&C 1/2 Ton is about 155 kg/cm, alternatively 868 lbs/inch.
Meaning: if you load 155 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 868 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for C&C 1/2 Ton is 16.9.

Low High 15% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 15% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for C&C 1/2 Ton is 2.97.

Slim Wide 66% 0 50 100
Compared with other similar sailboats it is more spacy than 66% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for C&C 1/2 Ton is 198 which categorizes this boat among 'light racers'.

Heavy Light 76% 0 50 100
76% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for C&C 1/2 Ton with ISO 8666 reference sail is 18.0, with a 135% genua the SA/D is 21.7.

Low High 73% 0 50 100
The SA/D ratio indicates that it is faster than 73% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 26m2 (279 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 27.2 m(89.2 feet)10 mm(3/8 inch)
Jib/genoa halyard27.2 m(89.2 feet)10 mm(3/8 inch)
Spinnaker halyard27.2 m(89.2 feet)10 mm(3/8 inch)
Jib sheet 9.3 m(30.4 feet)12 mm(1/2 inch)
Genoa sheet9.3 m(30.4 feet)12 mm(1/2 inch)
Mainsheet 23.2 m(76.0 feet)12 mm(1/2 inch)
Spinnaker sheet20.4 m(66.9 feet)12 mm(1/2 inch)
Cunningham2.8 m(9.3 feet)10 mm(3/8 inch)
Kickingstrap5.7 m(18.6 feet)10 mm(3/8 inch)
Clew-outhaul5.7 m(18.6 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for C&C 1/2 Ton it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References