Review of Tartan 46
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Tartan 46 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 378.0 liter fresh water capacity.
The Tartan 46 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Tartan 46 has been built with different keel alternatives.
CentreBoard
One option is a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.
The boat can enter even shallow marinas as the draft is just about 1.22 - 1.32 meter (4.00 - 4.30 ft) dependent on the load. See immersion rate below.
Fin keel
Another option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Tartan 46 can only enter major marinas as the draft is about 2.30 - 2.40 meter (7.55 - 7.85 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Westerbeke 4-107 diesel engine at 36 hp (26 kW). Calculated max speed is about 5.1 knots
The fuel tank has a capacity of 151.0 liters (39 US gallons, 33 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Tartan 46 is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Tartan 46 is about 328 kg/cm, alternatively 1839 lbs/inch.
Meaning: if you load 328 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1839 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Tartan 46 is 32.2.
What is L/B (Length Beam Ratio)?
The l/b ratio for Tartan 46 is 3.33.
What is Displacement Length Ratio?
The DL-ratio for Tartan 46 is 238 which categorizes this boat among 'light crusers & offshore racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Tartan 46 with ISO 8666 reference sail is 18.1, with a 135% genua the SA/D is 21.6.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 64m2 (688 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 42.1 m | (138.0 feet) | 14 mm | (0.55 inch) |
| Jib/genoa halyard | 42.1 m | (138.0 feet) | 14 mm | (0.55 inch) |
| Spinnaker halyard | 42.1 m | (138.0 feet) | 14 mm | (0.55 inch) |
| Jib sheet | 14.2 m | (46.7 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 14.2 m | (46.7 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 35.6 m | (116.7 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 31.3 m | (102.7 feet) | 16 mm | (5/8 inch) |
| Cunningham | 5.3 m | (17.5 feet) | 14 mm | (0.55 inch) |
| Kickingstrap | 10.7 m | (35.0 feet) | 14 mm | (0.55 inch) |
| Clew-outhaul | 10.7 m | (35.0 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Tartan 46 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.