Review of Optima HT

Basic specs.

The Optima HT is a sailboat designed by the Dutch maritime architect E. G. van de Stadt. The Optima HT is built by the German yard Dehler Yachtbau GmbH.

Here we would have liked to show you nice photos of the Optima HT.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Optima HT or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior

The boat is equipped with 6 berths, a galley and toilet facility.

Keel

Unknown keel type

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

Engine

Optima HT is typically equipped with an inboard Farymann engine at 10 hp (7 kW).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Optima HT is 1.92, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Optima HT is about 180 kg/cm, alternatively 1011 lbs/inch.
Meaning: if you load 180 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1011 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Optima HT is 3.16.

Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Optima HT is 50%.

This ballast ratio shows a righting moment that is higher than 92% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	9.2 m	(30.3 feet)	12 mm	(1/2 inch)
Genoa sheet	9.2 m	(30.3 feet)	12 mm	(1/2 inch)
Mainsheet	23.1 m	(75.7 feet)	12 mm	(1/2 inch)
Spinnaker sheet	20.3 m	(66.6 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Optima HT it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.