Review of Norlin 37
Basic specs.
Looking for a new boat? Find a Norlin 37 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 2 cabins, 7 berths, a galley, 200.0 liter fresh water capacity and toilet facility.
Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.
The Norlin 37 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
Fin keel
The Norlin 37 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Norlin 37 can only enter major marinas as the draft is about 1.95 - 2.05 meter (6.40 - 6.70 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an engine at 35 hp (26 kW). Calculated max speed is about 6.1 knots.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Norlin 37 is 1.90, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Norlin 37 is about 217 kg/cm, alternatively 1215 lbs/inch.
Meaning: if you load 217 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1215 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Norlin 37 is 28.0.
What is L/B (Length Beam Ratio)?
The l/b ratio for Norlin 37 is 3.07.
The ballast ratio for Norlin 37 is 53%.
What is Displacement Length Ratio?
The DL-ratio for Norlin 37 is 267 which categorizes this boat among 'light crusers & offshore racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Norlin 37 with ISO 8666 reference sail is 17.6, with a 135% genua the SA/D is 21.2.
What is Relative Speed Performance?
The Relative Speed Performance for Norlin 37 is 50
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 37m2 (398 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 35.3 m | (115.8 feet) | 12 mm | (1/2 inch) |
| Jib/genoa halyard | 35.3 m | (115.8 feet) | 12 mm | (1/2 inch) |
| Spinnaker halyard | 35.3 m | (115.8 feet) | 12 mm | (1/2 inch) |
| Jib sheet | 11.1 m | (36.3 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.1 m | (36.3 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 27.6 m | (90.6 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 24.3 m | (79.8 feet) | 14 mm | (0.55 inch) |
| Cunningham | 3.8 m | (12.5 feet) | 12 mm | (1/2 inch) |
| Kickingstrap | 7.6 m | (24.9 feet) | 12 mm | (1/2 inch) |
| Clew-outhaul | 7.6 m | (24.9 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Norlin 37 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.