Review of Alden O Class Mk II
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find an Alden O Class Mk II or similar boat for sale
The hull is made of wood.
The Alden O Class Mk II is built with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
CentreBoard
The Alden O Class Mk II is built with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.
The boat can sail close to the beach as the draft is just 0.29 - 0.39 meter (0.95 - 1.25 ft) dependent of the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Alden O Class Mk II is 2.11, indicating that this boat would not be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 5.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Alden O Class Mk II is about 63 kg/cm, alternatively 357 lbs/inch.
Meaning: if you load 63 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 357 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Alden O Class Mk II is 15.1.
What is L/B (Length Beam Ratio)?
The l/b ratio for Alden O Class Mk II is 2.73.
The ballast ratio for Alden O Class Mk II is 27%.
What is Displacement Length Ratio?
The DL-ratio for Alden O Class Mk II is 243 which categorizes this boat among 'light crusers & offshore racers'.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 19.36
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 5.5 m | (18.2 feet) | 8 mm | (5/16 inch) |
| Genoa sheet | 5.5 m | (18.2 feet) | 8 mm | (5/16 inch) |
| Mainsheet | 13.8 m | (45.4 feet) | 8 mm | (5/16 inch) |
| Spinnaker sheet | 12.2 m | (40.0 feet) | 8 mm | (5/16 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Alden O Class Mk II it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.