Review of Pop 16:2

Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

The Pop 16:2 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Fin keel

The Pop 16:2 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can enter even shallow marinas as the draft is just about 0.75 - 0.85 meter (2.46 - 2.76 ft) dependent on the load. See immersion rate below.

An outboard motor is often used on this boat. In that case Pop 16:2 will typically require a power of 1 - 2 hp, alternatively 22 - 26 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Pop 16:2 is 2.41, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Pop 16:2 is about 55 kg/cm, alternatively 310 lbs/inch.
Meaning: if you load 55 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 310 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Pop 16:2 is 10.0.

What is L/B (Length Beam Ratio)?

The l/b ratio for Pop 16:2 is 2.61.

What is a Ballast Ratio?

The ballast ratio for Pop 16:2 is 27%.

What is Displacement Length Ratio?

The DL-ratio for Pop 16:2 is 169 which categorizes this boat among 'light racers'.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Pop 16:2 with ISO 8666 reference sail is 17.9, with a 135% genua the SA/D is 19.9.

What is Relative Speed Performance?

The Relative Speed Performance for Pop 16:2 is 31

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 9m² (96 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Pop 16:2 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.