The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with a galley and toilet facility.
The Mascot 43 DS is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
Fin keel
The Mascot 43 DS is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The boat can only enter major marinas as the draft is about 1.80 - 1.90 meter (5.91 - 6.21 ft) dependent on the load. See immersion rate below.
Mascot 43 DS may be equipped with an inboard engine
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Mascot 43 DS is 1.97, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Mascot 43 DS is about 321 kg/cm, alternatively 1798 lbs/inch.
Meaning: if you load 321 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1798 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Mascot 43 DS is 27.3.
What is L/B (Length Beam Ratio)?
The l/b ratio for Mascot 43 DS is 3.05.
The ballast ratio for Mascot 43 DS is 38%.
What is Displacement Length Ratio?
The DL-ratio for Mascot 43 DS is 208 which categorizes this boat among 'light crusers & offshore racers'.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 51m2 (548 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 13.1 m | (42.8 feet) | 16 mm | (5/8 inch) |
Genoa sheet | 13.1 m | (42.8 feet) | 16 mm | (5/8 inch) |
Mainsheet | 32.6 m | (107.0 feet) | 16 mm | (5/8 inch) |
Spinnaker sheet | 28.7 m | (94.2 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Mascot 43 DS it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.