Review of Kendo 42
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Kendo 42 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 1003.0 liter fresh water capacity.
Fin keel
The Kendo 42 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The boat can only enter major marinas as the draft is about 1.85 - 1.95 meter (6.07 - 6.37 ft) dependent on the load. See immersion rate below.
Kendo 42 may be equipped with an inboard Perkins diesel engine
The fuel tank has a capacity of 500.0 liters (132 US gallons, 109 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Kendo 42 is 1.74, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Kendo 42 is about 277 kg/cm, alternatively 1556 lbs/inch.
Meaning: if you load 277 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1556 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Kendo 42 is 36.3.
What is L/B (Length Beam Ratio)?
The l/b ratio for Kendo 42 is 3.28.
The ballast ratio for Kendo 42 is 32%.
What is Displacement Length Ratio?
The DL-ratio for Kendo 42 is 288 which categorizes this boat among 'medium weight cruisers'.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 18.42
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 46m2 (495 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 12.9 m | (42.5 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 12.9 m | (42.5 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 32.4 m | (106.2 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 28.5 m | (93.5 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Kendo 42 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.