Review of Hunter 40.5 Legend

Basic specs.

The Hunter 40.5 Legend is a large sailboat designed by the maritime architect bureau Hunter Design Team in the early nineties. The Hunter 40.5 Legend is built by the American yard Hunter Marine.

Here we would have liked to show you nice photos of the Hunter 40.5 Legend.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Hunter 40.5 Legend or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 568.0 liter fresh water capacity.

Keel

Unknown keel type

The boat can enter even shallow marinas as the draft is just about 1.47 - 1.57 meter (4.82 - 5.12 ft) dependent on the load. See immersion rate below.

Engine

The Hunter 40.5 Legend has been equipped with different engine alternatives.

Alternative 1:

Hunter 40.5 Legend may be equipped with an inboard Yanmar diesel engine

Alternative 2:

The boat may be equipped with an inboard Volvo Penta engine

The fuel tank has a capacity of 151.0 liters (39 US gallons, 33 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hunter 40.5 Legend is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hunter 40.5 Legend is about 273 kg/cm, alternatively 1531 lbs/inch.
Meaning: if you load 273 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1531 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hunter 40.5 Legend is 3.23.

Compared with other similar sailboats it is more spacy than 58% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hunter 40.5 Legend is 35%.

This ballast ratio shows a righting moment that is higher than 27% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Hunter 40.5 Legend is 202 which categorizes this boat among 'light crusers & offshore racers'.

69% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Hunter 40.5 Legend with ISO 8666 reference sail is 16.5, with a 135% genua the SA/D is 19.0.

The SA/D ratio indicates that it is faster than 38% of all similar sailboat designs in light wind.

Over- / underrigged

The Hunter 40.5 Legend has more rig than 97% of all similar sailboats, which indicates that the boat is significantly overrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 42m² (452 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	40.9 m	(134.3 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	40.9 m	(134.3 feet)	12 mm	(1/2 inch)
Spinnaker halyard	40.9 m	(134.3 feet)	12 mm	(1/2 inch)
Jib sheet	12.2 m	(40.2 feet)	14 mm	(0.55 inch)
Genoa sheet	12.2 m	(40.2 feet)	14 mm	(0.55 inch)
Mainsheet	30.6 m	(100.4 feet)	14 mm	(0.55 inch)
Spinnaker sheet	26.9 m	(88.3 feet)	14 mm	(0.55 inch)
Cunningham	5.0 m	(16.4 feet)	12 mm	(1/2 inch)
Kickingstrap	10.0 m	(32.8 feet)	12 mm	(1/2 inch)
Clew-outhaul	10.0 m	(32.8 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Hunter 40.5 Legend it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.