Review of Glacer 44 Transocean

Basic specs.

The Glacer 44 Transocean is a large sailboat designed by the German maritime architect Hort E. Glacer in the early eighties. Only a few boats have been produced.

Here we would have liked to show you nice photos of the Glacer 44 Transocean.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Glacer 44 Transocean or similar boat for sale

Hull

The hull is made of aluminium. Aluminum is strong and forgiving. Where an impact on a fiberglass hull will result in major gelcoat damage and possible cracking, an aluminum hull will probably only have a scratch or a small bend. The only concern is electrolysis. Ensure that you have proper sacrificial anodes installed.

Keel

Fin keel

The Glacer 44 Transocean is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can only enter major marinas as the draft is about 1.84 - 1.94 meter (6.04 - 6.34 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Glacer 44 Transocean is 1.51, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Glacer 44 Transocean is about 294 kg/cm, alternatively 1650 lbs/inch.
Meaning: if you load 294 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1650 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Glacer 44 Transocean is 54.3.

Comparing this ratio with similar sailboats show that it is more comfortable than 100% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Glacer 44 Transocean is 3.35.

Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Glacer 44 Transocean is 26%.

This ballast ratio shows a righting moment that is higher than 4% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Glacer 44 Transocean is 398 which categorizes this boat among 'heavy cruisers'.

3% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Glacer 44 Transocean with ISO 8666 reference sail is 11.2, with a 135% genua the SA/D is 13.4.

The SA/D ratio indicates that it is faster than 1% of all similar sailboat designs in light wind.

Over- / underrigged

The Glacer 44 Transocean has more rig than 31% of all similar sailboats, which indicates that the boat is slightly underrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 48m² (516 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	37.8 m	(124.0 feet)	14 mm	(0.55 inch)
Jib/genoa halyard	37.8 m	(124.0 feet)	14 mm	(0.55 inch)
Spinnaker halyard	37.8 m	(124.0 feet)	14 mm	(0.55 inch)
Jib sheet	13.4 m	(44.0 feet)	16 mm	(5/8 inch)
Genoa sheet	13.4 m	(44.0 feet)	16 mm	(5/8 inch)
Mainsheet	33.5 m	(110.1 feet)	16 mm	(5/8 inch)
Spinnaker sheet	29.5 m	(96.9 feet)	16 mm	(5/8 inch)
Cunningham	4.5 m	(14.8 feet)	14 mm	(0.55 inch)
Kickingstrap	9.0 m	(29.5 feet)	14 mm	(0.55 inch)
Clew-outhaul	9.0 m	(29.5 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Glacer 44 Transocean it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.