Review of Signet 20
Basic specs.
Looking for a new boat? Find a Signet 20 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The boat is equipped with 4 berths and a galley.
Fin keel
The Signet 20 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can enter even shallow marinas as the draft is just about 0.91 - 1.01 meter (2.99 - 3.29 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Signet 20 is about 82 kg/cm, alternatively 460 lbs/inch.
Meaning: if you load 82 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 460 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Signet 20 is 2.98.
The ballast ratio for Signet 20 is 37%.
Maintenance
Dimensions of sail.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 16.9 m | (55.5 feet) | 6 mm | (1/4 inch) |
| Jib/genoa halyard | 16.9 m | (55.5 feet) | 6 mm | (1/4 inch) |
| Spinnaker halyard | 16.9 m | (55.5 feet) | 6 mm | (1/4 inch) |
| Jib sheet | 6.0 m | (19.8 feet) | 8 mm | (5/16 inch) |
| Genoa sheet | 6.0 m | (19.8 feet) | 8 mm | (5/16 inch) |
| Mainsheet | 15.1 m | (49.5 feet) | 8 mm | (5/16 inch) |
| Spinnaker sheet | 13.3 m | (43.6 feet) | 8 mm | (5/16 inch) |
| Cunningham | 2.7 m | (8.8 feet) | 6 mm | (1/4 inch) |
| Kickingstrap | 5.4 m | (17.6 feet) | 6 mm | (1/4 inch) |
| Clew-outhaul | 5.4 m | (17.6 feet) | 6 mm | (1/4 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Signet 20 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.