Review of Fisher 25

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 2 cabins, 5 berths, a galley, 220.0 liter fresh water capacity and toilet facility.

The Fisher 25 is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.

Full keel

The Fisher 25 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter even shallow marinas as the draft is just about 1.13 - 1.23 meter (3.71 - 4.01 ft) dependent on the load. See immersion rate below.

Fisher 25 may be equipped with an inboard Volvo Penta MD2B diesel engine at 25 hp (18 kW). The speed is 7.5 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 110.0 liters (29 US gallons, 24 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Fisher 25 is 1.73, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Fisher 25 is about 122 kg/cm, alternatively 684 lbs/inch.
Meaning: if you load 122 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 684 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Fisher 25 is 35.6.

What is L/B (Length Beam Ratio)?

The l/b ratio for Fisher 25 is 2.70.

What is a Ballast Ratio?

The ballast ratio for Fisher 25 is 43%.

What is Displacement Length Ratio?

The DL-ratio for Fisher 25 is 489 which categorizes this boat among 'heavy cruisers'.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 19m² (204 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Fisher 25 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.