Review of Ærø 35

Basic specs.

The Ærø 35 is a motorsailer designed in the mid nineties. The Ærø 35 is built by the Danish yard Æ B C Ærøskøbing Bådeværft & Chartercenter ApS.

Here we would have liked to show you nice photos of the Ærø 35.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Ærø 35 or similar boat for sale

Interior

The boat is equipped with 6 berths, a galley and 150.0 liter fresh water capacity.

Rig

The Ærø 35 is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.

Keel

Unknown keel type

The boat can enter even shallow marinas as the draft is just about 1.10 - 1.20 meter (3.61 - 3.91 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Ærø 35 is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Ærø 35 is about 220 kg/cm, alternatively 1235 lbs/inch.
Meaning: if you load 220 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1235 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Ærø 35 is 3.32.

Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Ærø 35 is 28%.

This ballast ratio shows a righting moment that is higher than 4% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	10.4 m	(34.3 feet)	12 mm	(1/2 inch)
Genoa sheet	10.4 m	(34.3 feet)	12 mm	(1/2 inch)
Mainsheet	26.1 m	(85.7 feet)	12 mm	(1/2 inch)
Spinnaker sheet	23.0 m	(75.4 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Ærø 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.