YachtDatabase.com

Review of Rhodes Reliant 41


Basic specs.

sail specifications
The Rhodes Reliant 41 is a large sailboat designed by the American maritime architect Philip L. Rhodes in the early sixties. Less than 100 boats have been produced.

Here we would have liked to show you nice photos of the Rhodes Reliant 41.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Rhodes Reliant 41 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 416.0 liter fresh water capacity.


Rig

The Rhodes Reliant 41 is equipped with a yawl rig. A yawl rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a yawl allows for better comfort and stability when sailing downwind or on a broad reach.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Rhodes Reliant 41 is 1.54, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Rhodes Reliant 41 is about 187 kg/cm, alternatively 1049 lbs/inch.
Meaning: if you load 187 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1049 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Rhodes Reliant 41 is 44.9.

Low High 98% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 98% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Rhodes Reliant 41 is 3.79.

Wide Slim 90% 0 50 100
Compared with other similar sailboats it is slimmer than 90% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Rhodes Reliant 41 is 448 which categorizes this boat among 'heavy cruisers'.

Heavy Light 1% 0 50 100
1% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Rhodes Reliant 41 with ISO 8666 reference sail is 14.7, with a 135% genua the SA/D is 17.3.

Low High 18% 0 50 100
The SA/D ratio indicates that it is faster than 18% of all similar sailboat designs in light wind.


Maintenance

Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 35.0 m(115.0 feet)12 mm(1/2 inch)
Jib/genoa halyard35.0 m(115.0 feet)12 mm(1/2 inch)
Spinnaker halyard35.0 m(115.0 feet)12 mm(1/2 inch)
Jib sheet 12.4 m(40.7 feet)14 mm(0.55 inch)
Genoa sheet12.4 m(40.7 feet)14 mm(0.55 inch)
Mainsheet 31.1 m(101.9 feet)14 mm(0.55 inch)
Spinnaker sheet27.3 m(89.6 feet)14 mm(0.55 inch)
Cunningham5.0 m(16.3 feet)12 mm(1/2 inch)
Kickingstrap9.9 m(32.6 feet)12 mm(1/2 inch)
Clew-outhaul9.9 m(32.6 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Rhodes Reliant 41 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References