Review of Raider 35

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

The boat is equipped with one cabin, 5 berths, a galley, 246.0 liter fresh water capacity, toilet facility and 57.0 liter waste water capacity.

The Raider 35 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Fin keel

The Raider 35 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can enter most marinas as the draft is just about 1.52 - 1.62 meter (4.99 - 5.29 ft) dependent on the load. See immersion rate below.

The Raider 35 has been equipped with different engine alternatives.

Alternative 1:

Raider 35 may be equipped with an inboard Yanmar 3GM30 diesel engine at 27 hp (20 kW). Calculated max speed is about 5.0 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

Alternative 2:

The boat may be equipped with an inboard Universal M35 diesel engine at 35 hp (26 kW). Calculated max speed is about 5.7 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank, which is made of stainless steel, has a capacity of 57.0 liters (15 US gallons, 12 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Raider 35 is 1.73, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Raider 35 is about 159 kg/cm, alternatively 890 lbs/inch.
Meaning: if you load 159 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 890 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Raider 35 is 34.9.

What is L/B (Length Beam Ratio)?

The l/b ratio for Raider 35 is 3.33.

What is Displacement Length Ratio?

The DL-ratio for Raider 35 is 443 which categorizes this boat among 'heavy cruisers'.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 26m² (279 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Raider 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.